Perbandingan Efisiensi Biaya Berdasarkan Perhitungan Struktur Pada Kerangka Atap Menggunakan Baja Ringan dan Baja Berat Dengan Bentang 14.5 M

Faizal Mahmud, Kukuh Wisnuaji Widiatmoko

Abstract


Structural analysis of lightweight steel roof truss and heavy steel roof truss (conventional) spans 14.5 m in terms of cost and work efficiency. The roof truss studied consisted of: truss distance of 1.5 m for mild steel, and 3.75 m for heavy steel, with a slope angle of 20°, the roof covering on both uses sheet metal tile. Modeling and calculating this of level damages (ratio) and roof truss deflection use SAP 2000. The Budget Plan is calculated based on the PUPR Ministerial Regulation 28-2016 using the 2021 unit price. From this research, the results obtained are reduction percentage in price per unit meter2 of light steel roof truss. against heavy steel roof trusses reached 42.84%. Both models (light steel and heavy steel) have ratio and deflection values that are within safe limits, namely the ratio of 0.850114 for mild steel, 0.733239 for heavy steel, and deflection of 0.00054 for mild steel, 0.000075 for heavy steel.

Keywords


Light Steel, Conventional Steel, Cost

Full Text:

PDF

References


Husnah, Husnah dkk. 2019. “Analisis Struktur Rangka Baja Ringan Dan Baja Berat Dengan Aplikasi Bricscad.” Jurnal Teknik Sipil, Vol.5, No.2.

Nasional, Badan Standardisasi. 2002. “SNI 03-1729-2002 Tata Cara Perencanaan Struktur Baja Untuk Bangunan Gedung.”

Nasional, Badan Standardisasi. 2013. “SNI-03-1727-2013 Beban minimum untuk perencanaan bangunan gedung dan struktur lain.”

Nasional, Badan Standardisasi. 2015. “SNI 1729 : 2015 Spesifikasi untuk bangunan gedung baja structural.”

Puri, Wuwuh Asrining. 2013. “Red Bricks And Light Bricks Cost Analysis For Walls And Mild Steel And Wood For Roof Truss (BPN Office Construction Case Study in Mojokerto Regency),” EXTRAPOLASO : Jurnal Teknik Sipil 6(01).

Purwanto, Herri. 2019. “Analisis Efisiensi Konstruksi Rangka Atap Baja Ringan.” Jurnal Deformasi 2(1).

Rahmawati, C., Zainuddin, Z., Is, S., & Rahim, R. (2018). Comparison between PCI and Box Girder in BridgesPrestressed Concrete Design. Journal of Physics: Conference Series, 1007(1). https://doi.org/10.1088/1742-6596/1007/1/012065

Rahmawati, Cut, & Zainuddin, Z. (2016). Analysing The Route Of PCI Girder-Type Prestressed Concrete Tendons. International Journal of Science and Research (IJSR), 5, 1553–1559.




DOI: https://doi.org/10.30601/jtsu.v8i2.2807

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Faizal Mahmud, Kukuh Wisnuaji Widiatmoko

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Jurnal Teknik Sipil Unaya


Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

© Jurnal Teknik Sipil Unaya : Published by Center for Research and Community Service (LPPM) University of Abulyatama, Aceh, Indonesia. 2019